Ask a tradesperson
Plastering
一般建议如果/如何重新呈现
I moved into a large detached 1920s house, fully rendered, about a year ago. The render hasn't been painted for a long time. Trying now to make a decision now about the order of doing things including whether to re render or (for now) patch and paint.
1. I have 18 windows in various states of repair, many of which will probably need replacing over a number of years (due to cost), including 3 large bays. There are also 50m of old cracked soffits (not asbestos) that are about a foot deep that will need replacing. If I re render now, is it possible to replace windows / soffits over time without ending up with an awful finish on the render - is it easy to make good and match after doing these kind of jobs?
2. The current render is blown in small patches. If I were to instead get the current render painted, would an exterior decorator expect to patch small bits as part of the job, or would it need a separate job for plasterer to investigate and patch everything before the decorator comes in?
3. I live in an area with lots of oak trees. They stain car paint and window paint so I have to clean regularly. I've read that silicon / krend can be susceptible to this staining and ultimately require painting. Is this true and/or should I consider a different kind of render in this kind of environment?
Appreciate this is long question(s) but it's a big house and I'm trying to plan for next 10 years and feel the order of doing things could be very important!
4 Answers from MyBuilder Plasterers
Best Answer
Croydon•Member since 12 May 2015•35jobs,100%positivefeedback
1.My advise would be to sort your windows out first
2.Get advise on the extent of the damage render
3.If blown make plans to have it redone
I am not a fan of krend as a good sand and cement render using the right sand will always look better.
Answered 10th Aug 2019
Manchester•Member since 1 Oct 2018•5jobs,100%positivefeedback
I would not use sand and cement render as you can not guarantee it won’t crack again and there is the upkeep of painting there are better products available now, but widows should definitely be your 1st job.
Krend is really bad for staining but silicone silicate can be cleaned,
in an area like that I wouldn’t recommend any render but if you had to go with one I would say silicone silicate. rendering should be your last job to get done
Answered 10th Aug 2019
Thetford•Member since 12 Aug 2019•No feedback yet
Like Simmonds Plastering, I would start with sorting the windows out first.
Then the Render. 1920’s you are still around period of Lime Renders, soft bricks as the change to cement wasn’t really in full affect until the 30’s. So if you was to get a plasterer / renderer in, look to get a Lime plaster specialist to have a look. They’d look to see what the substrate is and so on.
K-rend is said to be breathable but it’s always going to fail on the movement part. And the ‘non maintenance’ part isn’t true. You’ll need to clean it
Answered 13th Aug 2019
Headley, Surrey•Member since 3 Nov 2017•17jobs,88%positivefeedback
1.Always attend to the windows first.
2. Inspect the state of render, if blown remove.
3. Replace with Monouche as this needs no maintanince and if done correctly using the full system including mesh cloth there will be no problems with the render blowing or cracking.
Answered 16th Aug 2019
Related Questions
- I want to damp proof my celler using a membrane system and would like some advice on how to calculate my materials.
HI, I have decided that I will damp proof my celler using a platon waterproof membrane and then make a frame for the...
- How to re-tile on to a wooden bathroom window sill/recess?
Hi, I have some tiles that have popped off on the vertical side of a bathroom window recess. I've remove all the tiles along...
- Advice needed on how to change a washer on a free-standing control panel that won't open
Hi I have a free-standing shower control panel, make unknown, and it does not give hot water so I am assuming the washer needs...
- Advice needed on how to change a washer on a free-standing control panel that won't open
Hi I have a free-standing shower control panel, make unknown, and it does not give hot water so I am assuming the washer needs...
Post your job to find high quality tradespeople and get free quotes
Question Categories
- All Questions
- Architectural Services
- Bathroom Fitting
- Bricklaying
- Carpentry & Joinery
- Carpet & Lino
- Central Heating
- Chimneys & Fireplaces
- Conservatories
- Conversions - General
- Damp Proofing
- Demolition & Waste Clearance
- Driveways
- Electrical
- Extensions
- 筋膜,索夫its & Guttering
- Fencing
- Gas Work
- Groundwork & Foundations
- Handyman
- Hard Flooring
- Insulation
- Kitchen Fitting
- Landscape Gardening
- Locksmiths
- Loft Conversions
- New Builds
- Painting & Decorating
- Plastering
- Plumbing
- Restoration & Refurbishment
- Roofing
- Security Systems
- Stonemasonry
- Tiling
- Tree Surgery
- Windows